Rudder Trim Tab?
Forum rules
A forum for Panther aircraft builders and Enthusiasts. Two simple rules: Play nice and use a real name
A forum for Panther aircraft builders and Enthusiasts. Two simple rules: Play nice and use a real name
-
xtricity
- Posts: 4528
- Joined: Sat May 03, 2025 12:43 am
- First Name: Mess
- Last Name: None
- City or Town: TBS
- State or Province: None
-
xtricity
- Posts: 4528
- Joined: Sat May 03, 2025 12:43 am
- First Name: Mess
- Last Name: None
- City or Town: TBS
- State or Province: None
-
xtricity
- Posts: 4528
- Joined: Sat May 03, 2025 12:43 am
- First Name: Mess
- Last Name: None
- City or Town: TBS
- State or Province: None
-
xtricity
- Posts: 4528
- Joined: Sat May 03, 2025 12:43 am
- First Name: Mess
- Last Name: None
- City or Town: TBS
- State or Province: None
-
xtricity
- Posts: 4528
- Joined: Sat May 03, 2025 12:43 am
- First Name: Mess
- Last Name: None
- City or Town: TBS
- State or Province: None
-
xtricity
- Posts: 4528
- Joined: Sat May 03, 2025 12:43 am
- First Name: Mess
- Last Name: None
- City or Town: TBS
- State or Province: None
-
GlenNJ
- Posts: 152
- Joined: Sun May 19, 2013 8:11 am
- First Name: Glen
- Last Name: Robinson
- City or Town: Marmora
- State or Province: NJ
- Location: Marmora, New Jersey
Re: Rudder Trim Tab?
Thanks Tony and Bob,
That sounds easier and better than riveting on a trim tab.
Glen
That sounds easier and better than riveting on a trim tab.
Glen
-
Tony Spicer
- Posts: 304
- Joined: Sun May 05, 2013 7:35 am
- First Name: Tony
- Last Name: Spicer
- State or Province:
- Location: Wilmington, NC 7NC1
Re: Rudder Trim Tab?
Glen,
It's an Avery part: http://www.averytools.com/searchprods.asp RV guys don't mind paying $15 for a little piece of plastic. Panther builders have the talent to make one from scratch. 1 1/2" wide, 3/8" at the trailing edge, and about 8" long. You can hack one out of a piece of wood in about 2 minutes. Tape it to the appropriate side of the rudder. Go fly at your favorite cruising speed. Shorten tab until ball is in center. A coat of epoxy and a couple coats of rattle can primer, then paint and attach with the double-sided tape Bob told you about.
Tony
It's an Avery part: http://www.averytools.com/searchprods.asp RV guys don't mind paying $15 for a little piece of plastic. Panther builders have the talent to make one from scratch. 1 1/2" wide, 3/8" at the trailing edge, and about 8" long. You can hack one out of a piece of wood in about 2 minutes. Tape it to the appropriate side of the rudder. Go fly at your favorite cruising speed. Shorten tab until ball is in center. A coat of epoxy and a couple coats of rattle can primer, then paint and attach with the double-sided tape Bob told you about.
Tony
-
GlenNJ
- Posts: 152
- Joined: Sun May 19, 2013 8:11 am
- First Name: Glen
- Last Name: Robinson
- City or Town: Marmora
- State or Province: NJ
- Location: Marmora, New Jersey
Re: Rudder Trim Tab?
Bob,
I looked on Van's web store site, but I couldn't find the wedges you suggested. I used Van's search engine and typed in "Rudder Trim Tab". The only hit I got said: Trim Tab & Rivets
12 Rudder Trim Kit
$7.00
I'm not sure what this is, because there wasn't a picture. Are the wedges on the Van's Air Force site?
Glen
I looked on Van's web store site, but I couldn't find the wedges you suggested. I used Van's search engine and typed in "Rudder Trim Tab". The only hit I got said: Trim Tab & Rivets
12 Rudder Trim Kit
$7.00
I'm not sure what this is, because there wasn't a picture. Are the wedges on the Van's Air Force site?
Glen
-
woolleys
- Posts: 49
- Joined: Sun May 19, 2013 8:27 am
- First Name: Bob
- Last Name: Woolley
- City or Town: Green Cove Springs
- State or Province: Florida
Re: Rudder Trim Tab?
Glen, instead of drilling and putting a permanent tab on the rubber. I would suggest that you use a wedge or bend tab on the side of the rudder, ie: vans RV install. Once you get the right size after flying, you then affix it to the rudder via automotive double sided trim tape. Thus no holes in the rudder that leads to cracks in the rudder.
Bob Woolley
Bob Woolley